All Brands
Dryer Repair in Las Vegas
Clothes still damp after an hour, or a drum that will not turn, usually come down to heat, airflow or a worn drive part. We check all three.
Phones answered 24/7
Brands We Service
Houses, Condos, Rentals & Garages
How a Repair Visit Works
Related Services
Other appliance and brand repairs we handle in the south and southwest Las Vegas Valley.
Dryer Problems We Diagnose
The dryer problems listed here cover heat, tumbling, overheating, noise and slow drying on gas, electric and compact models.
- Not Heating
- Drum Not Tumbling
- Takes Too Long to Dry
- Making Loud Noise
- Won't Start
- Dryer Overheating
- Not Drying Clothes
- Shutting Off Early
- Not Getting Hot Enough
- Taking Too Long to Dry
- Thermal Fuse Blown
- Heating Element Burned Out
- Gas Igniter Not Working
- Gas Valve Solenoid Failure
- Flame Sensor / Radiant Sensor Failure
- Blower Wheel Clogged with Lint
- Exhaust Duct Clogged
- Restricted Exhaust Airflow
- Dryer Venting Improperly
- Drive Belt Broken
- Drum Rollers Worn Out
- Drum Glide / Bearing Worn
- Idler Pulley Seized
- Drive Motor Failure
- Making Loud Noise During Operation
- Squealing Noise During Tumble
- Thumping or Banging Noise
- Rattling Noise
- Control Board Failure
- Cycling Thermostat Failure
- High-Limit Thermostat Failure
- Moisture Sensor Failure
- Dryer Door Not Closing Properly
- Door Switch Failure
- Lint Trap / Screen Damaged
- Start Button Not Working
- Dryer Won't Turn On
- Tripping Circuit Breaker
- Burning Smell
- Clothes Shrinking
- Clothes Still Wet After Full Cycle
- Clothes Damp but Warm After Cycle
- Auto-Dry Sensor Not Working
- Timer Not Advancing
- Electric Dryer No Heat — Partial Power
- Gas Smell from Gas Dryer
- Display Panel Not Working
- Buttons Not Responding
- Won't Spin at All
- Stops Mid-Cycle
- Heat Setting Not Changing
- Excessive Energy Use
- Excessive Static on Clothes
- Clothes Heavily Wrinkled
- Steam Function Not Working
- Moisture Sensor Needs Cleaning
- Exhaust Hose Kinked
- Exterior Too Hot to Touch
- Wrinkle-Prevent Tumble Not Working
- Requires Two or More Cycles to Dry
- Error Code on Display
- Low Gas Pressure to Dryer
- Drum Interior Light Not Working
- Door Handle Broken
- Auto-Dry Cycle Runs All Night
- Gas Burner Orifice Clogged
- Lint Fire Hazard in Ductwork
- Timer Advancing Too Slowly
- Three-Prong Outlet / Four-Prong Cord Mismatch
- Knocking at Startup
- Intermittent Squeaking
- Bird or Pest Nest in Dryer Duct
- Cycling Thermostat Stuck Closed
- Gas Valve Solenoid Kit Needed
- Thermal Cutout Needs Resetting
Dryer Brands We Service
Dryer Repair Questions
Straight answers to what people ask before booking. If your question isn't here, send it with your booking request and we'll answer it.
Still have questions?
We cover 15 ZIP codes in Enterprise, Spring Valley, Paradise and southern Henderson.
A thermal fuse is a one-time safety device that opens when the exhaust gets too hot. Replacing it without finding the reason usually means another blown fuse within weeks. The cause is most often a restricted vent, but a cycling thermostat stuck closed or a heating element shorting to the cabinet can do it too. We look at both the machine and the duct.
No. A hot or burning smell can mean lint has collected near the heat source or that a part is overheating. Turn the dryer off, unplug it, and for a gas model close the gas shutoff behind the machine. Clean the lint screen and look for a crushed transition hose, but have the dryer inspected before running it again.
That pattern often points to weak gas valve coils. The igniter lights the burner, but as the coils warm up they stop holding the valve open, so the flame drops out and the drum cools. A failing flame sensor or a restricted vent can look similar, so the technician tests each before quoting.
We inspect the vent on every dryer call and clear the transition hose and the reachable section behind the machine when it is part of the fault. Long wall or roof runs, typical in two-story stucco homes, sometimes need dedicated vent-cleaning equipment, and we will tell you if that is the case.
Close the gas shutoff valve on the supply line first, then unplug the power cord. Slide the dryer out slowly so you do not kink the flexible gas connector or crush the vent hose. If the connector looks old, corroded or stiff, have it replaced rather than reusing it.
No. We are an independent repair company and are not factory-authorized by any manufacturer. If your dryer is still under the manufacturer's warranty, contact the manufacturer first, since work by an independent shop may not be covered. Out-of-warranty dryers get manufacturer-specified parts by default and a 90-day parts and 30-day labor warranty on the repair.
Dryer repair in the Las Vegas Valley
A dryer has only a few systems: a motor that turns the drum and blower, a heat source, and the exhaust path that carries moist air outside. Electric models heat with a coiled element, gas models with an igniter and valve coils. When drying slows or stops, one of those systems is almost always involved.
In valley homes, airflow deserves extra attention. Dryers often sit in hot garages or vent through long runs inside stucco walls, and lint packed into those ducts slows drying, trips thermal fuses and raises fire risk. Good dryer repair includes checking the exhaust as well as the machine, so a new part is not sent back into the same conditions.
Clues from the laundry room
Common reports include a dryer that runs cold, one that needs two or three cycles, a cabinet that feels too hot to touch, or a squeal and thump as the drum turns. Some machines refuse to start at all, which often traces to a blown thermal fuse or a door switch.
A burning smell, or lint visible around the back of the machine, means stop using it and have the airflow checked.
Where dryers break down
On electric dryers, burned-out heating elements, cycling thermostats and high-limit thermostats are routine. Gas dryers add igniters, flame sensors and gas valve coils, which tend to fail in a pattern where the flame lights briefly and then drops out.
Mechanical wear shows up as broken belts, flat-spotted drum rollers, worn idler pulleys and glides, and motors whose bearings have dried out.
Dryers by brand
We service Whirlpool, Maytag, Kenmore, Roper and Amana dryers that share common platforms, Samsung and LG models with sensor-dry and steam features, GE and Electrolux pairs, compact Bosch, Miele and ASKO units, including heat-pump and condensing designs, and Speed Queen machines.
Testing heat, motion and exhaust
The technician confirms supply first (240 volts on electric models, gas and spark on gas models), then checks the fuses, thermostats and heat source with a meter. Belt, rollers and motor get a hands-on inspection, and airflow is measured or observed at the exhaust hood.
You see one price for parts and labor before any work starts. If the duct is part of the problem, we say so instead of replacing parts that would fail again.
Reasons to book TrueFix for a dryer
Our phone is staffed 24/7, and evening or weekend calls cost no more. When a same-day slot opens up we take it, though we never promise one in advance. Repairs carry 90 days of coverage on the parts installed and 30 days on the labor, and we install manufacturer-specified parts by default.